S6730-H24X6C 02352FSG Huawei 24x10Gb SFP+ and 6x40/100Gb QSFP28 Ports Switch
S6730-H24X6C 02352FSG Huawei 24x10Gb SFP+ and 6x40/100Gb QSFP28 Ports Switch
Version Mapping
Table 4-187 lists the mapping between the S6730-H24X6C chassis and software versions.
Table 4-187 Version mapping
Series | Model | Software Version |
|---|---|---|
S6730-H | S6730-H24X6C | 02352FSG: V200R013C02 and later versions 02352FSG-001: V200R020C10 and later versions 02352FSG-005: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.) 02352FSG-007: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.) 02352FSG-009: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.) 02353GFC: V200R013C02 and later versions 02353GFC-001: V200R020C10 and later versions 02353GFC-003: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.) 02353GFC-004: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.) NOTE:V200R021C01 is not supported. Some models cannot be downgraded due to component upgrade. Therefore, you are advised to run the display system-software information command (supported in V200R021C00 and later versions) to check the software versions supported by the device before performing a downgrade. |
Appearance and Structure
Figure 4-82 S6730-H24X6C appearance
1 | Twenty-four 10GE SFP+ ports Applicable modules and cables:
| 2 | Six 40GE/100GE QSFP28 optical ports Applicable modules and cables:NOTE:A QSFP28 optical port cannot be split into four 10GE ports, regardless of whether the port uses a QSFP28 or QSFP+ optical module. For the S6730-H24X6C (part number: 02352FSG/02352FSG-001/02352FSG-005/02352FSG-007/02352FSG-009):
For the S6730-H24X6C (part number: 02353GFC/02353GFC-001/02353GFC-003/02353GFC-004), the license has been activated and QSFP28 ports on the switch work as 100GE ports. |
3 | Ground screw NOTE: It is used with a ground cable. | 4 | SSD card slot NOTE:This slot is reserved for future use. |
5 | One console port | 6 | One ETH management port |
7 | One USB port | 8 | One PNP button NOTICE:To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button. |
9 | Fan module slot 1 NOTE:Applicable fan module: FAN-031A-B (Fan Box (B, Fan Panel Side Exhaust)) | 10 | Fan module slot 2 NOTE:Applicable fan module: FAN-031A-B (Fan Box (B, Fan Panel Side Exhaust)) |
11 | Fan module slot 3 NOTE:Applicable fan module: FAN-031A-B (Fan Box (B, Fan Panel Side Exhaust)) | 12 | Fan module slot 4 NOTE:Applicable fan module: FAN-031A-B (Fan Box (B, Fan Panel Side Exhaust)) |
13 | Power module slot 1 NOTE:Applicable power module:
| 14 | Power module slot 2 NOTE:Applicable power module:
|
Port Description
10GE SFP+ optical port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-188 describes the attributes of a 10GE SFP+ Ethernet optical port.Table 4-188 Attributes of a 10GE SFP+ port
Attribute | Description |
|---|---|
Connector type | LC/PC |
Optical port attributes | Depend on the optical module used |
Standards compliance | IEEE802.3ae |
Working mode | GE/10GE auto-sensing |
40GE/100GE QSFP28 optical port
A 40GE/100GE QSFP28 optical port sends and receives service traffic at 40 Gbit/s or 100 Gbit/s. Table 4-189describes the attributes of a QSFP28 optical port.Table 4-189 Attributes of a QSFP28 optical port
Attribute | Description |
|---|---|
Connector type | MPO/LC |
Optical port attributes | Depend on the optical module used |
Standards compliance | IEEE802.3ba |
Console port
The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-190.Table 4-190 Attributes of a console port
Attribute | Description |
|---|---|
Connector type | RJ45 |
Standards compliance | RS-232 |
Working mode | Duplex Universal Asynchronous Receiver/Transmitter (UART) |
Baud rate | 9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s |
ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-191 describes the attributes of an ETH management port. Table 4-191 Attributes of an ETH management port
Attribute | Description |
|---|---|
Connector type | RJ45 |
Standards compliance | IEEE802.3 |
Working Mode | 10/100 Mbit/s auto-sensing |
Maximum transmission distance | 100 m |
In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration.
USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.
Indicator Description
The S6730-H24X6C has the same types of indicators as the S6730-H48X6C. For details, see Indicator Description.
Power Supply Configuration
The switch can use a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.
Heat Dissipation
The S6730-H24X6C uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.
This figure only shows the airflow direction and does not depict the actual device.
Technical Specifications
Table 4-192 lists technical specifications of the S6730-H24X6C.
Table 4-192 Technical specifications
Item | Description |
|---|---|
Memory (RAM) | 4 GB |
Flash | 2 GB in total. To view the available flash memory size, run the display versioncommand. |
Mean time between failures (MTBF) | 62.27 years |
Mean time to repair (MTTR) | 2 hours |
Availability | > 0.99999 |
Service port surge protection | N/A |
Power supply surge protection |
|
Dimensions (H x W x D) |
|
Weight (with packaging) | 8.9 kg (19.62 lb) |
Stack ports |
|
RTC | Supported |
RPS | Not supported |
PoE | Not supported |
Rated voltage range |
|
Maximum voltage range |
|
Maximum power consumption (100% throughput, full speed of fans) | 254 W |
Typical power consumption (30% of traffic load, tested according to ATIS standard) | 149 W |
Operating temperature | -5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F). The operating temperature of the switch is -5°C to 40°C (23°F to 104°F) when it uses QSFP-100G-ER4 optical module. |
Storage temperature | -40°C to +70°C (-40°F to +158°F) |
Noise under normal temperature (27°C, sound power) | < 65 dB(A) |
Relative humidity | 5% to 95%, noncondensing |
Operating altitude | 0-5000 m (0-16404 ft.) |
Certification |
|
Part number | 02352FSG 02352FSG-001 02352FSG-005 02352FSG-007 02352FSG-009 02353GFC 02353GFC-001 02353GFC-003 02353GFC-004 |